Recommend:
To the knowledge base
Knowledge document #636

Cannot access the internet via the FRITZ!Box

You don't have internet, although internet access is set up in the FRITZ!Box? ✔ Here's what to do.

Although the FRITZ!Box is connected to a fiber optic connection (Fiber to the Home, FTTH) and configured to access the internet over fiber optics, some or all of the computers, smartphones, or other devices connected to the FRITZ!Box cannot access the internet. One of the following messages may be displayed on the devices:

  • "No Internet, secured"
  • "No Internet access"
  • "No internet connection"
  • "Connected to device. Can't provide internet"

Important:If you are using the FRITZ!Box with a different fiber optic modem, proceed as described in the guide Cannot access the internet via a different modem.

Simply proceed as described below. After each measure, check whether the problem is solved.

Note:All instructions on configuration and settings given in this guide refer to the latest FRITZ!OS for the FRITZ!Box.

1 Issue occurred after updating FRITZ!OS

Only follow the instructions in the following guide if the error occurred immediately after a FRITZ!OS update:

  1. Cannot connect to the internet since FRITZ!OS update

2 Unlocking your FRITZ!Box

If you purchased your FRITZ!Box from a retailer, your internet service provider may have to unlock it first:

Modem ID on the FRITZ!Box's type label
  1. Contact the customer service of your internet service provider and have them unlock the FRITZ!Box for your fiber optic connection, if necessary. Depending on the provider, you can either call their customer service or use an activation portal to activate it.
    • With some providers, the FRITZ!Box's "modem ID" given on the type label is required to unlock it.

3 Checking the connection to the FRITZ!Box

For the device to access the internet via the FRITZ!Box, it must be connected to the FRITZ!Box and able to access it:

Deactivating the mobile network connection in Android

In some cases it may only be possible to access the user interface with an Android smartphone or tablet when the mobile network connection is cleared. The user interface can always be reached, even without internet access:

  1. Enable airplane mode on the Android device to clear all connections.
  2. Only enable Wi-Fi on the Android device to establish the connection to the FRITZ!Box.

Opening the FRITZ!Box user interface

  1. Open the FRITZ!Box user interface with the device that cannot access the internet.
  2. If the device can access the user interface, continue with the next section. If you used an Android device to access the user interface, you can now deactivate airplane mode on it again.

4 Checking the fiber optic connection

  1. Open the FRITZ!Box user interface.
  2. Check whether "Fiber Optics" is displayed as connected in the section "Connections and Interfaces" on the "Overview" page.
  3. If "Fiber Optics" is displayed as "interrupted", follow the steps in our guide FRITZ!Box's Power LED flashes.

5 Checking the event log of the FRITZ!Box

  1. Click "System" in the FRITZ!Box user interface.
  2. Click "Event Log" in the "System" menu and then "Internet Connection".
  3. Check whether one of the following error messages is displayed and follow the instructions in the corresponding guide:

6 Enabling the FRITZ!Box's DHCP server

In the factory settings, the FRITZ!Box automatically assigns the correct IP settings to all devices via DHCP. If you disabled the FRITZ!Box's DHCP server, re-enable it:

  1. Click "Home Network" in the FRITZ!Box user interface.
  2. Click "Network" in the "Home Network" menu.
  3. Click on the "Network Settings" tab.
  4. Click "Additional Settings" in the section "WAN setting" or "LAN Settings" to display all of the settings.
  5. Click the "IPv4 Settings" button.
  6. Enable the DHCP server and define the range from which the FRITZ!Box assigns IP addresses.

    Note:The FRITZ!Box has the IP address 192.168.178.1 (subnet mask 255.255.255.0) and assigns IP addresses from xxx.20 to xxx.200 in the factory settings.

  7. Click "Apply" to save the settings.

7 Configuring the device to automatically obtain IP settings

To ensure that the device always uses the correct IP settings, make sure that it automatically obtains its IP settings from the FRITZ!Box (this is the default setting for most devices):

  1. Configure the device to automatically obtain IP settings via DHCP.

8 Configuring a DNS server in the FRITZ!Box

In the factory settings, the FRITZ!Box uses the DNS server of the internet service provider for the name resolution of web addresses. If you set up other DNS servers in the FRITZ!Box, re-enable the DNS server of the internet service provider:

  1. Click "Internet" in the FRITZ!Box user interface.
  2. Click "Account Information" in the "Internet" menu.
  3. Click on the "DNS Server" tab.
  4. Enable the option "Use DNSv4 servers assigned by the internet service provider (recommended)".
  5. If the section "DNSv6 Servers" is displayed, enable the option "Use DNSv6 servers assigned by the internet service provider (recommended)".
  6. If the option "Encrypted name resolution in the internet (DNS over TLS)" is enabled, enable the option "Allow fallback to non-encrypted name resolution in the internet".
  7. Click "Apply" to save the settings and on the FRITZ!Box, confirm that the procedure may be executed, if you are asked to do so.

9 Installing the latest software for the device

  1. Install the latest software version for the device (for example Android, iOS) or the latest driver for the computer's network adapter.

    Note:
    Since Windows Update often does not offer the latest drivers, install the drivers from the manufacturer's website, for example from the Intel Download Center.

10 Configuring the device's firewall

The following step is only necessary if firewall software is installed on the device:

  1. Configure the firewall on the device so that it allows connections from the device to the FRITZ!Box. Refer to the manufacturer of the firewall for information on how to set it up, for example consult the manual.
Language selection