Recommend:
To the knowledge base

DSL connection drops frequently

The FRITZ!Box's DSL connection drops often and the Power/DSL LED flashes? ✔ Here's what to do.

The DSL connection between the FRITZ!Box and your DSL provider's exchange drops several times a day. During this time, the Power LED on the FRITZ!Box flashes and then stays lit as soon as the internet connection is re-established.

The following error message is displayed in the event log of the FRITZ!Box:

"DSL not responding (no DSL synchronization)
DSL synchronization starting (training)"

Cause

  • The stability of the DSL connection depends primarily on the length and quality of the access line. Faults in the cabling or problems with the internet service provider's exchange (DSLAM) can also affect it.

Simply proceed as described below. After each measure, check whether the problem is solved.

Note:All instructions on configuration and settings given in this guide refer to the latest FRITZ!OS for the FRITZ!Box.

1 Checking the event log of the FRITZ!Box

  1. Click "System" in the FRITZ!Box user interface.
  2. Click "Event Log" in the "System" menu.
  3. Check whether events also took place before the time when the error occurred, or whether only events are shown that took place after the error occurred.
  4. If events are also displayed that took place before the time the error occurred, proceed with the next section.
  5. If the message "The internet connection (DSL) was cleared. Interference may have been caused by powerline" is displayed, follow the steps in our guide FRITZ!Box reports "Interference may have been caused by powerline".

2 Checking the cabling

It is often difficult to recognize faults in the cabling and they can remain unnoticed for a long time. Therefore, check the wiring in your home:

  1. Remove the DSL splitter if you are using the FRITZ!Box on an IP-based connection.
  2. Remove all cable extensions, unused cables, telephone jacks, and additional electrical components (for example surge protection, automatic extension outlets).
  3. Make sure that the FRITZ!Box is correctly connected to your DSL line.

3 Limiting DSL sync rate

Some DSL providers usually do not limit the data rate of the DSL connection (DSL sync rate), but reduce the data rate to the agreed value at the IP level instead. As a result, the FRITZ!Box always establishes the DSL connection with the highest data rate possible, which makes the connection more susceptible to interference. Therefore, limit the DSL sync rate to the value agreed on:

  1. Click "Internet" in the FRITZ!Box user interface.
  2. Click "DSL Information" in the "Internet" menu.
  3. Click on the "Interference Resistance" ("Line Settings") tab.
  4. Click "Interference Resistance Settings" to display all of the settings.
  5. Enable the option "Limit DSL sync rate to the available bit rate". If the option is not displayed, either the DSL provider limits the DSL data rate to the bit rate agreed on or they do not transmit a value for the bit rate agreed on to the FRITZ!Box.
  6. Click "Apply" to save the settings.

4 Using a different DSL version

The DSL version of the FRITZ!Box undergoes constant development with each FRITZ!OS to ensure that it can establish optimal DSL connections under all circumstances. In individual cases (for example on DSL lines with outdated DSLAMs) the FRITZ!Box may only be able to establish an error-free DSL connection with certain DSL versions. Therefore, test the current and the previous DSL version:

Using the latest FRITZ!OS

The DSL version is part of FRITZ!OS. Make sure that the FRITZ!Box is using the latest FRITZ!OS and therefore the latest DSL version:

  1. Install the latest FRITZ!OS on the FRITZ!Box.

Using the previous DSL version

If the problem occurs with the latest DSL version (for example after updating FRITZ!OS), test the DSL version of the previous FRITZ!OS:

  1. Click "Internet" in the FRITZ!Box user interface.
  2. Click "DSL Information" in the "Internet" menu.
  3. Click on the "Interference Resistance" ("Line Settings") tab.
  4. Click "Interference Resistance Settings" to display all of the settings.
  5. Enable the option "Use previous DSL version".
  6. Click "Apply" to save the settings.
  7. Now the FRITZ!Box enables the previous DSL version and will then restart. The restart will take about two minutes.

5 Increasing the interference resistance

Increase the interference resistance of your DSL connection so that the DSL connection no longer drops or does not drop as often when there are brief disturbances on the DSL line:

Note:Increasing the interference resistance of the DSL connection may slightly reduce the data rate of the DSL connection.

  1. Click "Internet" in the FRITZ!Box user interface.
  2. Click "DSL Information" in the "Internet" menu.
  3. Click on the "Interference Resistance" ("Line Settings") tab.
  4. Click "Interference Resistance Settings" to display all of the settings.
  5. Move the control "Intended signal-to-noise ratio" one step farther towards "maximum stability".

    Important:If you move the controls too far towards "maximum stability", with some DSL lines you may no longer be able to establish a DSL connection. Therefore, do not select the setting "maximum stability" right away. Instead, move the controls step by step to the left to determine the best setting for your DSL line.

  6. Click "Apply" to save the settings.
  7. If the DSL connection continues to drop frequently, repeat steps 5 - 7 until the DSL connection is stable.

6 Testing a different cable

The cable that connects the FRITZ!Box with the DSL line could be defective. Test a different DSL cable:

  1. Use a different DSL cable (for example, from another DSL modem) to connect the FRITZ!Box to the DSL line.
  2. If the DSL connection no longer drops, the DSL cable you used before is damaged and must be replaced.

    Note:You can either purchase a new DSL cable from an electronics retailer, or order it from us by sending an email to zubehoer@avm.de. You can also make your own DSL cable using the guide Assignment of cables, adapters, and sockets.

7 Checking the DSL line

There may be a problem with the DSL line. Since it may take a while for your DSL provider to check your line, you may be charged for the service, and our experience shows that there is often a problem with DSL lines even if they have been checked by your provider, proceed as follows:

  1. Disconnect the FRITZ!Box from the DSL line.
  2. Connect a different DSL modem to the DSL line.
  3. Test whether the DSL connection remains stable when you use this DSL modem.
  4. If the connection continues to drop, have your provider check your line. There is a problem with the DSL line.

    ATTENTION!You may be charged for checking. Ask your provider about charges in advance!